Rotating Eyebolt H.Q. – Grade 100 – Cartec

Anchorage point for load lifting

• Safety coefficient 4 in all loading directions
• Designed, tested and certified in compliance with the technical directives GS-OA 15-04 – EN 1677
• Suitable for safe lifting in compliance with the Machinery Directive 2006/42/EC
• Can be oriented at 360°
• Tested at 100% magnaflux
• Tested at 20.000 fatigue cycles
• Ideal for fastening at 90°
• Captive screws
• On the axial pull there can be a variation of +/- 5° with a 10% decrease in capacity

The eyebolt with the product code C807X is Grade 100, for the heat-treated version of the product click here

SAFETY INSTRUCTIONS

FORESEEN USE

Anchorage point for load lifting

NOT SUITABLE FOR LIFTING PEOPLE

CE Conformity Declaration

(Machinery Directive 2006/42/EC all. IIA)

We declare that all materials specified in the present declaration are in compliance with all the dispositions related to the Directive 2006/42/EC

CHECK SUITABILITY OF ROTATING EYEBOLTS ART.800 BEFORE USE AND YEARLY

Before each use make sure that:

• The eyebolt and its components including the screw do not have defects due to wear, corrosion, cracks or visible deformations
• Markings are clearly legible.
• The loads to be lifted are in compliance with the rated capacities of the eyebolt (the working load limits are specified on the eyebolt and in the user manual).
• The diameter of the welded ring has not been reduced by more than 10% of the nominal diameter due to wear at any contact point.
• The eyebolt is lightly screwed into the supporting structure and the bulb rotates freely.

If these checks give a negative outcome, the eyebolt must not be used any more, and must be replaced.

Please remember:

• Inspections must be carried out by qualified personnel.
• Checks have to be carried out by a qualified staff as the rotating eyebolts series 800 must undergo checks at regular intervals and scheduled in compliance with the laws in force
• The rotating eyebolt with ring must only be installed and used by trained personnel of legal working age, following the Machinery Directive 2006/42/EC and its subsequent amendments.
• The qualified person must supervise the lifting operation and must always detect the gravity center of the load and position the eyebolts in order to guarantee that the said load is always balanced
• If the load is asymmetrical take into consideration a decrease of the capacity as shown on the reference chart
• Check suitability of the resistance class of the mother screw which has to house the eyebolt with the ration of the load to be lifted (the material of the mother screw has to have traction resistance which is the same or higher than steel S235JR – norm of reference UNI EN 10025)
• The depth of the threaded hole has to be minimum
  1*d for steel
  1.25*d for cast iron
  1.5*d for cast iron castings with low resistance (resistance <200 MPa)
  2*d for aluminum alloys
  2.5*d for aluminum – magnesium alloys
• The threaded hole must be perpendicular to the surface
• Make sure that the surtace of the mother screw is suitable for the planarity and dimension in order to guarantee touching of all the surface of the eyebolt and that it adheres suitably. They eyebolt cannot be used with parts of the tilting surface
• To install the eyebolt simply manually lock the screw with a proper torque without the aid of extension leads which could preload the screw with excessive torque (do not exceed torque specified in the chart). To disassemble, unscrew
• Lock the eyebolt until it fits completely onto the surface
• Tighten the eyebolt until it is fully seated on the surface.

Warning! The eyebolt doesn’t rotate on its axis with the screw locked

• Ambient Temperature Load Limit Reduction
  • <-40°C Not permitted
  • -40°C to +200°C None
  • +200°C to +250°C -20%
  • +250°C to +350°C -25%
  • > +350°C Not permitted
• Safety Coefficient 4
• For lifting devices that remain attached to the structure we recommend the part being locked by means of thread brake glue
• On the axial pull there can be variation of +/5o with a 10% decrease in capacity
• The eyebolt can be used safely up to maximum of 20.000 lifts with a full load
• For risky lifting operations safety measures have to be taken for the people who undergo the risk
• If the instructions are not adhered to serious damage can be caused to things and injuries to people
• This documentation has been prepared in compliance with section 1.7.4.2 of the Machinery Directive 2006/42/EC.

NOT ALLOWED:

• Do not use eyebolts in acid high corrosion chemical substance environment and/or in an explosive atmosphere
• Do not use in environments with temperatures above +350°C or below -40°C
• Do not exceed the capacity specified on the reference chart
• Do not used for operations which defer from the ones that are foreseen
• Do not use locking screws which are larger than the ones specified to assemble the eyebolt
• Do not use to life people
• Do not stand under an overhanging load whilst it is being used
• Do not stand during use in dangerous areas (dangerous areas means areas which are deemed risky due to falling of load during movement with accessories)
• If changes, repairs and/or treatments are made to the product, the terms of the guarantee are no longer applicable and the manufacturer declines all liability.

STORAGE:
The device must be stored in a suitable environment (e.g., dry, non-corrosive).

DISPOSAL:
The product packaging must be sent for normal recycling.
The product must be recovered as metal scrap