Eyebolt 8.8 – Grade 80 – Cartec

Hand-screwed high-strength steel shackle. Compatible with shackles of suitable strength, it offers reliability in industrial, marine, and construction applications. Complies with the requirements of the Machinery Directive 2006/42/EC.

The eyebolt with the product code C803 is Grade 80

SAFETY INSTRUCTIONS

FORESEEN USE

Eyebolt for Load Lifting

NOT SUITABLE FOR LIFTING PEOPLE

CE Conformity Declaration

(Machinery Directive 2006/42/EC all. IIA)

We declare that all materials specified in the present declaration are in compliance with all the dispositions related to the Directive 2006/42/EC

CHECK SUITABILITY OF ROTATING EYEBOLTS ART.800 BEFORE USE AND YEARLY

Before each use make sure that:

The eyebolt shows no defects due to wear, corrosion, cracks, or visible deformations.
Markings are clearly legible.
The loads to be lifted are in compliance with the rated capacities of the eyebolt (the working load limits are specified on the eyebolt and in the user manual).
The diameter of the welded ring has not been reduced by more than 10% of the nominal diameter due to wear at any contact point.
The eyebolt is screwed tightly into the supporting structure

If these checks give a negative outcome, the eyebolt must not be used any more, and must be replaced.

Checks have to be carried out by a qualified staff as the rotating eyebolts series 800 must undergo checks at regular intervals and scheduled in compliance with the laws in force
The rotating eyebolt with ring must only be installed and used by trained personnel of legal working age, following the Machinery Directive 2006/42/EC and its subsequent amendments.
The qualified person must supervise the lifting operation and must always detect the gravity center of the load and position the eyebolts in order to guarantee that the said load is always balanced
If the load is asymmetrical take into consideration a decrease of the capacity as shown on the reference chart
Check suitability of the resistance class of the mother screw which has to house the eyebolt with the ration of the load to be lifted (the material of the mother screw has to have traction resistance which is the same or higher than steel S235JR – norm of reference UNI EN 10025)
The depth of the threaded hole has to be minimum
1*d for steel
1.25*d for cast iron
1.5*d for cast iron castings with low resistance (resistance <200 MPa)
2*d for aluminum alloys
2.5*d for aluminum – magnesium alloys
The threaded hole must be perpendicular to the surface
To install: manually screw in the eyebolt using a wrench. Do not use extension bars or tools that can over-torque the bolt. Do not exceed the recommended torque in the chart.
For lifting devices that remain attached to the structure we recommend the part being locked by means of thread brake glue
For risky lifting operations safety measures have to be taken for the people who undergo the risk
If the instructions are not adhered to serious damage can be caused to things and injuries to people

CAPACITY REDUCTION FACTORS

Ambient Temperature Load Limit Reduction
• <-20°C Not permitted
• -20°C to +100°C None
• +100°C to +200°C -15%
• +200°C to +250°C -20%
• +250°C to +350°C -25%
• >+350°C Not permitted

This documentation has been prepared in compliance with section 1.7.4.2 of the Machinery Directive 2006/42/EC.

NOT ALLOWED:

Do not use eyebolts in acid high corrosion chemical substance environment and/or in an explosive atmosphere
Do not use in environments with temperatures above +350°C or below -20°C
Do not exceed the capacity specified on the reference chart
Do not used for operations which defer from the ones that are foreseen
Do not use extension cords ( lever ) to lock the eyebolt
Do not use locking screws which are larger than the ones specified to assemble the eyebolt
Do not use to life people
Do not stand under an overhanging load whilst it is being used
Do not stand during use in dangerous areas (dangerous areas means areas which are deemed risky due to falling of load during movement with accessories)
If changes, repairs and/or treatments are made to the product, the terms of the guarantee are no longer applicable and the manufacturer declines all liability