Lifting Ring Weld-On Type Single Base – Grade 100 – Cartec

Lifting Ring Weld-On Type Single Base anchorage point for load lifting.

Safety Coefficient 4
The entire perimeter of the base must be welded except for the water discharge area.
For asymmetric loads remember that the capacity has to be reduces as shows in the reference table.
The bracket must always be aligned to the pulling direction (tolerance allowed +/-10°)
The anchorage clamp can be used safely up to a maximum of 20.000 lifts with a full load
Ring tested at 100% magnaflux.
Made in high resistant steel
Painted with epoxy paint
Tested at 20.000 fatigue cycles
In particular applications the capacity which has to be used must be determined by the pulling inclination angle following the following formula:

The eyebolt with the product code C830X is Grade 100, for the corresponding eyebolt for lashing click here.

SAFETY INSTRUCTIONS

FORESEEN USE

Lashing eyebolt weld-on type for load lifting.

NOT SUITABLE FOR LIFTING PEOPLE

CE Conformity Declaration

(Machinery Directive 2006/42/EC all. IIA)

We declare that all materials specified in the present declaration are in compliance with all the dispositions related to the Directive 2006/42/EC

CHECK SUITABILITY OF ROTATING EYEBOLTS ART.800 BEFORE USE AND YEARLY

Before each use make sure that:

The eyebolt and the base shows no defects due to wear, corrosion, cracks, or visible deformations.
Markings are clearly legible.
The loads to be lifted are in compliance with the rated capacities of the eyebolt (the working load limits are specified on the eyebolt and in the user manual).
The diameter of the welded ring has not been reduced by more than 10% of the nominal diameter due to wear at any contact point.
The weld is intact and shows no wear, corrosion or cracks

If these checks give a negative outcome, the eyebolt must not be used any more, and must be replaced.

Please remember:

Inspections must be carried out by qualified personnel.
Checks have to be carried out by a qualified staff as the rotating eyebolts series 800 must undergo checks at regular intervals and scheduled in compliance with the laws in force

THE WELD

The lifting clamp to be welded must be fitted by a qualified person as it is used for lifting operations which must be conducted in compliance with machinery directive 2006/42/EC and subsequent modifications
The qualified person supervising the lifting operations must always identify the load’s centre of gravity and position the lifting clamp in such a way as to guarantee that the load is always balanced
If the load is asymmetrical take into consideration a decrease of the capacity as shown on the reference chart
Welding must be done by a qualified person in accordance with standard EN ISO 9606
The bases to be welded are made of S355J2+N steel
The welding bead must be round and closed
For ring to be welded with spring:

Attentions: Weld the base of the clamp with the ring in a vertical position. To avoid compromising the functionality of the spring please wait for the welding point to cool down before inclining/orientating the ring.

The minimum thickness of the weld bead is shown on the reference chart.
The welding bead must be of the HV type and must have a continuous angle. This weld complies with the DIN 18800 standard
To weld the lifting clamp, the preheated temperature must be between 130°C and 170°C.
Never weld directly forged and tempered clamps (painted in peach) and avoid heating these clamps during welding.
Avoid the sudden cooling of the weld
Position the eyebolt in accordance with the load to be lifted taking care to avoid unauthorised stresses such as load twisting or overturning

CAPACITY REDUCTION FACTORS

Ambient Temperature Load Limit Reduction
• <-20°C Not permitted
• -20°C to +200°C None
• +200°C to +300°C -10%
• +300°C to +400°C -25%
• >+400°C Not permitted

Safety Coefficient 4

THE SUPPORTING WALL

Ensure that it is suitable for welding (ordinary steal with max carbon content of 0.40%); for safety’s sake, request approval from the manufacturer
Ensure that there are no surface defects, cracks or roughness
Ensure that it is suitably flat in order to guarantee a good foundation for the surface of the base to be welded
Ensure that it is large enough to prevent deformations or stress ruptures
The ring must always be aligned to the pulling direction (tolerance allowed +/-10°)
The hook may be used safely for up to 20,000 full-load lifting cycles.
For risky lifting operations safety measures have to be taken for the people who undergo the risk
If the instructions are not adhered to serious damage can be caused to things and injuries to people
This documentation has been prepared in compliance with section 1.7.4.2 of the Machinery Directive 2006/42/EC.

NOT ALLOWED:

Do not use eyebolts in acid high corrosion chemical substance environment and/or in an explosive atmosphere
Η χρήση σε θερμοκρασίες εκτός του εύρους -20°C έως 400°C.
Do not exceed the capacity specified on the reference chart
Do not used for operations which defer from the ones that are foreseen
Do not use to life people
Do not stand under an overhanging load whilst it is being used
Never weld directly the forged and tempered clamps (painted in peach) and avoid heating these clamps during welding
Do not stand during use in dangerous areas (dangerous areas means areas which are deemed risky due to falling of load during movement with accessories)
If changes, repairs and/or treatments are made to the product, the terms of the guarantee are no longer applicable and the manufacturer declines all liability.

STORAGE:

The device must be stored in a suitable environment (e.g. dry, non-corrosive, etc.)

DISPOSAL:

The product packaging must be sent for normal recycling

The product must be recovered as metal scrap